Motorola launched the Moto G Power, back in February 2020 along with Moto G Stylus and it is expected to hit the market in April 2020. The device comes out of the box with Android 10 and expected to receive future updates just like other Moto G series.

Today Motorola has finally rolled the Android 11 update to the Moto G Power globally which brings all the Android 11 features and customization. In this guide, we will show you how to install the Android 11 firmware file manually on Moto G Power.

Also Read

List of Best Custom ROM for Motorola Moto G8 Power [Updated]

Download and Install AOSP Android 13 on Motorola Moto G8 Power / Moto G Power

Quick Specs Review

The newly announced Motorola Moto G Power is another budget category smartphone that offers a massive battery and triple rear cameras with macro support. There are no drastic differences between the Moto G Stylus and Moto G Power except for the battery, cameras, and a stylus pen. While the SD665 chipset offers good multitasking, the big honking battery can last more than a day on a single charge very easily. Most importantly, under the 10K price tag, it’s a stunning device with a nice look and feels.

The Moto G Power comes with a 6.4-inches IPS LCD display with a resolution of 1080×2300 pixels that has a pixel density of 399 PPI and more than 83% screen-to-body ratio. It runs on Android 10 and powered by Snapdragon 665 processor along with Adreno 610 GPU. The handset packs 4GB of RAM and 64GB of eMMC 5.1 storage with a dedicated microSD card slot.

It packs a triple rear camera setup of 16MP (wide, f/1.7) + an 8MP (ultrawide, f/2.2) + 2MP (macro, f/2.2) lens with an LED flash, PDAF, HDR, Panorama, etc. It supports 2160p@30fps, 1080p@30/60fps, 1080p@30fps video recording with gyro-EIS. While the front packs a 16MP (wide, f/2.0) selfie shooter with HDR mode. It features 1080p@30/120fps video recording.

The handset sports a 3.5mm headphone jack, dual-band Wi-Fi 802.11 a/b/g/n/ac, GPS, Bluetooth 5.0, A-GPS, GLONASS, BDS, GALILEO, FM Radio, USB 2.0 Type-C port. It packs a giant 5,000mAh battery with 10W charging. The device features a rear-mounted fingerprint sensor, an accelerometer, gyro, an ambient light, proximity sensor.

Download Moto G Power Android 11 Update

Here you can download the official Android 11 for the Moto G Power.

Steps to Install Moto G Power Android 11 Update

Now, if you’re ready to flash the Android 11 manually on your Moto G Power device then you need to download the drivers, firmware file, and tools. So, without wasting any more time, let’s get into it.

Pre-Requirements:

  • This ROM is supported for the Moto G Power variant only.
  • Make sure that your device should be charged at least 50% or higher.
  • You will require a PC or Laptop with a USB Data Cable.
  • We always recommend our readers take a full data backup of the device for safety purposes.
  • Install Motorola USB Drivers and Rescue and Smart Assistant Tool on your PC
  • Download ADB and Fastboot Tool or Android SDK Platform tool

Firmware Installation Guide:

Check out the firmware flashing guide below for the Moto G Power. First, make sure to install or extract the adb and fastboot tool on your PC. Now enter the bootloader on your device.

Disclaimer:

Step 1. Bootloader Mode

Enter bootloader mode on your phone. To boot first, turn your phone off. Once your device turned off completely, press and hold the volume down, and turn it on. You should see the bootloader screen.

Step 2. Connect Your Device to PC:

After booting your Moto G Power into bootloader mode, now connect it to the PC using the USB Cable.

Step 3. Download Stock ROM/Firmware:

To get the full ROM, you can use the LMSA or Rescue and Smart Assistant Tool. Download the zip file and copy it to somewhere on your PC. LMSA tool will unzip the file and will remove the zip file you downloaded.

Advertisement

You can also download the full stock ROM from the above download flash file section on this guide.

Step 4. Flashing Guide:

  • The next step is to open the command window and go to the adb folder
  • Enter the following command to flash the firmware.
  • fastboot flash partition gpt.bin
  • fastboot flash bootloader bootloader.img
  • fastboot flash vbmeta_system vbmeta_system.img
  • fastboot flash vbmeta vbmeta.img
  • fastboot flash radio radio.img
  • fastboot flash bluetooth BTFM.bin
  • fastboot flash dsp dspso.bin
  • fastboot flash logo logo.bin
  • fastboot flash boot boot.img
  • fastboot flash vendor_boot vendor_boot.img
  • fastboot flash dtbo dtbo.img
  • fastboot flash super super.img_sparsechunk.0
  • fastboot flash super super.img_sparsechunk.1
  • fastboot flash super super.img_sparsechunk.2
  • fastboot flash super super.img_sparsechunk.3
  • fastboot flash super super.img_sparsechunk.4
  • fastboot flash super super.img_sparsechunk.5
  • fastboot flash super super.img_sparsechunk.6
  • fastboot flash super super.img_sparsechunk.7
  • fastboot flash super super.img_sparsechunk.8
  • fastboot flash super super.img_sparsechunk.9
  • fastboot erase userdata
  • fastboot erase ddr
  • fastboot oem fb_mode_clear
  • fastboot reboot
  • Now your device will reboot into bootloader with the firmware you installed.

That’s it, guys. We hope this guide was helpful to you. Feel free to ask in the comment below for additional queries.

fastboot flash partition gpt.bin fastboot flash bootloader bootloader.img fastboot flash vbmeta_system vbmeta_system.img fastboot flash vbmeta vbmeta.img fastboot flash radio radio.img fastboot flash bluetooth BTFM.bin fastboot flash dsp dspso.bin fastboot flash logo logo.bin fastboot flash boot boot.img fastboot flash vendor_boot vendor_boot.img fastboot flash dtbo dtbo.img fastboot flash super super.img_sparsechunk.0 fastboot flash super super.img_sparsechunk.1 fastboot flash super super.img_sparsechunk.2 fastboot flash super super.img_sparsechunk.3 fastboot flash super super.img_sparsechunk.4 fastboot flash super super.img_sparsechunk.5 fastboot flash super super.img_sparsechunk.6 fastboot flash super super.img_sparsechunk.7 fastboot flash super super.img_sparsechunk.8 fastboot flash super super.img_sparsechunk.9 fastboot erase userdata fastboot erase ddr fastboot oem fb_mode_clear fastboot reboot